Silica gel 硅胶

TEROSON MS 939 is a single-component, black, white, or gray, low modulus, flexible, odorless modified silane adhesive used for elastic sealing. It can cure into a UV-resistant thermosetting elastomer. It has excellent sag resistance and strong initial tack. This product is non-corrosive and does not contain solvents, isocyanates, siloxanes, or polyvinyl chloride. The curing speed can be accelerated by using LOCTITE MS 9371B.

TEROSON MS 930 is a single-component, white, gray, or black, moisture-curing, thixotropic modified silane sealant/adhesive. This product is suitable for various applications involving different substrates. It can form a flexible elastomer with excellent UV resistance and weatherability.

TEROSON PU 9100 is a one-component polyurethane sealing product designed for joint and seam sealing. It has a surface drying time of 35 minutes. It is applied using a tool with a piston rod, such as the TEROSON ET STAKU HAND GUN. For optimal application, the TEROSON POWERLINE II COMPRESSED AIR GUN or TEROSON ET AIR GUN MULTIPRESS can be used. It is recommended to clean the surface with TEROSON VR 10 for best results.

LOCTITE® SI 598 is a metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. It cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. It resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. This product is typically used in applications with an operating range of -54 to +260°C.

LOCTITE SI 5910 is a low strength, silicone based flange sealant designed for use on machined or cast flexible flange surfaces (metal or plastic). This product is suitable for gaps of 1 mm or less and provides a fully cured volume of 2.75 mm (within 24 hours). Typical applications include stamping sheet metal covers (such as timing case covers and oil pans.)

Alkoxy silicone gasketing and sealant paste which resists weathering, moisture, ozone and retains its properties through severe environments.
LOCTITE SI 5084 is a straw-colored, translucent, high strength, non-corrosive, alkoxy silicone gasketing and sealant paste which resists weathering, moisture, ozone and retains its properties through severe environments. It enhances the load bearing and shock absorbing characteristics of the bond area.

LOCTITE HHD 9393 BK is one component silane modified polymers, which has high bonding strength on many substrates. This product cures by reaction with moisture to an elastic product. The skin formulation and curing times are dependant on humidity and temperature, and the curing time also depends on joint depth. By increasing the temperature and moisture these times can be reduced; low temperature as well as low moisture retard the process. LOCTITE HHD 9393 BK is free of solvents, isocyanates, silicones and PVC and has only weak odour (after curing it is odourless). It demonstrates good adhesion without primer to many substrates.

Clear, 1-part, thixotropic, room temperature-cure, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor.
LOCTITE SI 595 is a clear, 1-part, thixotropic, room temperature vulcanizing, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor. It is designed as an excellent adhesive sealant for mechanical assemblies. Typical applications include electrical insulation, protection of leads from mechanical shock, trim bonding, and sealing of ductwork, vents, flues, doors, and windows.

LOCTITE ABLESTIK 59C, Silicone, Heat cure
LOCTITE ABLESTIK 59C adhesive is designed for applications used at high temperatures which require electrical conductivity and do not need a high bond strength. It can be used in its cured or uncured state. LOCTITE ABLESTIK 59C can be used with a variety of catalysts. For more information on mixed properties when used with other available catalysts, please contact your local technical service representative for assistance and recommendations.

LOCTITE 567 là chất bịt kín ren methacrylate có độ bền tháo rời thấp, màu trắng nhạt, được UL phê duyệt, lý tưởng để bịt kín các ren thô lên đến M80/R3”.
LOCTITE 567™ là keo dán ren methacrylate thixotropic, có màu trắng nhạt, độ bền thấp. Nó đông cứng trong điều kiện không có không khí và khi tiếp xúc với kim loại khi được giới hạn trong các ren lên đến M80/R3”. Nó phù hợp nhất để sử dụng trên các sợi kim loại thô và định mức mô-men xoắn đột phá của nó là 1,7Nm. Độ nhớt là 280.000 - 800.000 mPa·s và nhiệt độ sử dụng -65° đến +400°F (-55 đến +200ºC). UL đã được phê duyệt.